Electricians repair, install and maintain residential, commercial and industrial electrical systems. 

Electricians usually start their work by reading blueprints that show the locations of circuits, outlets, load centers, panel boards, and other equipment. 

Electricians connect all types of wires to circuit breakers, transformers, outlets, or other components.  Hand tools such as conduit benders, screwdrivers, pliers, knives, hacksaws, and wire strippers, as well as power tools such as drill and saws are used.  They pull wires or cables through conduits (pipe or tubing). 

Electricians may install coaxial or fiber optic cable for telecommunications equipment and electronic controls for industrial uses. 

By the end of this program, students should be prepared to take the Journeyman’s Exam.

CAREER OPPORTUNITIES:  Journeyman Maintenance Electrician, Journeyman Electrician, Water Plant Electrician, Industrial Electrician, High Voltage Electrician, Electrical and Instrumentation Technician, Plant Electrician, Self-Employed

Tool Lists

Program Handbook

 
Admission Criteria
Prior to enrollment student must:

• Successfully complete preadmission testing

Associate of Applied Science Degree: 71 Credits. To complete the Associate of Applied Science Degree, select 15 more credits from the General Education requirements found in the Degree and Certification Information.  Visit with your instructor or the Vice President of Student Services for possible options.

First Year/First Semester

CON 101 Introductory Craft Services, 3 credits.
This course follows the NCCER modules for:  Basic Safety, Introduction to Construction Math, Introduction to Hand Tools, Introduction to Power Tools, Introduction to Blueprints, Basic Rigging, Basic Communication Skills, and Basic Employability Skills.

ENV 102 Safety Orientation (OSHA 10), 1 credit.
This course provides students with an understanding of current safety regulations, established safety practices, hazard recognition, and the impact of behavior and environment on injury prevention.

ELT 140 NEC 1, 4 credits.
This course covers the first part of the National Electrical Code on residential and commercial wiring.  This will include definitions, requirements for electrical installation, wiring design and protection, methods and materials, equipment for general use, special equipment, and condition.

ELT 108 Blueprint Reading, 2 credits.
This course will cover all the symbols and schematics needed for an electrician to correctly install, maintain, and troubleshoot residential, commercial, or industrial wiring according to plans and electrical equipment.

ELT 111 Residential Wiring 1, 4 credits.
This course will cover the basics of residential electrical wiring.  Students will learn both theory of electricity as well as how to install and troubleshoot wiring problems.

Back to top

First Year/Second Semester

ELT 141 NEC 2, 2 credits. (Prerequisite: ELT 140 NEC 1)
This course covers the second part of the National Electrical Code on industrial wiring.  This will include definitions, requirements for electrical installation, wiring design and protection, methods and materials, equipment for general use, special equipment, and condition.

ELT 160 Commercial Wiring 1, 4 credits.
This course covers all aspects of commercial wiring.  Included in this course will be reading of commercial blueprints, applying knowledge to hands-on applications of commercial wiring techniques, and safety.

ELT 220 Motor Control, 4 credits. (Prerequisite: ELT 107 AC/DC Circuits 1)
Students will learn construction and operation of pilot devices, motor starters, control circuits, direct current, single-phase and three-phase motors.  Basic motor control circuits are constructed from a schematic or ladder diagram.  Students also troubleshoot basic motor control circuits.  Current and overload protection for motors is studied as well.

ELT 250 Generators and Emergency Systems 4 credits.
Students will learn to work with installation, termination, and testing of various voice, data, and video cabling systems.  They will understand the installation of electric circuits in health care facilities, including the requirements for life safety and critical circuits.  In addition, the course covers the NEC requirements for electric generators and storage batteries.  Fire alarm control units, Digital Alarm Communicator Systems (DACS), wiring for alarm initiating and notification devices, and alarm system maintenance will also be covered.

Back to top

Second Year/First Semester

ELT 150 Transformers, 2 credits. (Prerequisite: ELT 107 AC/DC Circuits 1)
In this course students will learn the basic electrical and magnetic principles as applied to transformers as well as advanced principles of transformer operations.  The course will also cover safety, standards for electrical devices, maintenance, and troubleshooting.

ELT 205 Industrial Wiring 1, 2 credits.
This course covers all aspects of industrial wiring.  Included in this course will be reading of industrial blueprints, applying knowledge to hands-on applications of industrial wiring techniques, safety, conduit bending and systems, and sizing of feeders and circuits for motor systems.

ELT 107 AC/DC Circuits 1, 4 credits.
This course is an introduction to electrical and electronic components, symbols, and the global language used in electrical and electronics. Students receive computer-based, modular training simultaneously with practical experience reading schematic diagrams, constructing circuits, and test procedures of operating characteristics used in AC/ DC circuits. Students will measure frequency and voltages with meters and oscilloscopes and learn about frequency reactive devices.

ELT 240 NEC 3, 2 credits. (Prerequisite: ELT 141 NEC 2)
This course covers the second part of the National Electrical Code on industrial wiring.  This will include definitions, requirements for electrical installation, wiring design and protection, methods and materials, equipment for general use, special equipment, and condition.

ELT 230 Troubleshooting, 2 credits. (Prerequisite: ELT 111 Residential Wiring 1 or ELT 160 Commercial Wiring 1)
In this course students will learn how to deal with customers, observe system operations, formulate a plan, read and interpret schematics and perform operational checks.

ELT 255 Advanced Automation and Controls, 2 credits
Upon completion of the course, students will have a comprehensive overview of applications and operating principles of solid-state controls, reducing-voltage starters, and adjustable frequency drives.  The course covers a basic overview of HVAC systems and their controls, electrical troubleshooting and NEC requirements.

Back to top

Second Year/Second Semester

ELT 225 PLC I (Programmable Logic Control), 4 credits. (Prerequisite:  ELT 220 Motor    Control)
This course will cover additional motor control features such as programmable logic controllers (PLCs), relays, timers, sensing devices, system integration, and preventive maintenance and troubleshooting.

ELT 206 Industrial Wiring II, 2 credits.  (Prerequisite: ELT 205 Industrial Wiring 1)
This course continues the learning began in Industrial Wiring 1 by moving on to more advanced skills.

ELT 260 Journeyman’s Exam Prep, 4 credits.
This course will prepare the student to take the Journeyman Electrician Exam.  The course will cover all components of the exam—terminology, formulas, wiring methods, over current protection, calculations and sample examinations.

ELT 270 OJT/Internship, 4 credits.  (Prerequisite:  Instructor permission)
Students will apply classroom knowledge to an actual work situation. OJT/Internship will provide students with on-the-job experience under the supervision of professionals in the industry.  The work will be developed cooperatively with area employers, college staff, and each student to provide a variety of actual job experiences directly related to the student’s career goals.

Back to top

GAINFUL EMPLOYMENT

The Higher Education Opportunity Act (HEOA) requires Salina Area Technical College to report about its graduates' gainful employment. In order to be eligible for funding under the Title IV programs, an educational program must lead to a certificate or degree (associate, bachelor's, graduate, or professional) or prepare students for "gainful employment in a recognized occupation" (GE Programs). Complete information on the GE Program requirements is available on the designated Gainful Employment Information Page that can be found at http://ifap.ed.gov/GainfulEmploymentInfo/.

Electrical Technology